Categories
Recently Viewed Items
Home >> ECUTOOL Products>> Emulators
TMS374 ECU Decoder
Item No. 3502054
Item Name TMS374 ECU Decoder
Item Price US$21.67
Weight 35 Gram
Quantity 102 PCS in stock now!
I want buy PCS
      

Introduction for TMS374 ECU Decoder

This Tool is a frequency sweeper with 5V square wave output (Duty cycle 50%, effective frequency range from over 10kHz (max 50kHz) to 50Hz). This tool can be also considered as a MCU version of the software TMS-374 Decoder ECU. The only difference between the two tools is that the MCU version works without a PC. A small MCU is used to generate the pulses instead of the PC RS232 Tx line.

Descriptions for TMS374 ECU Decoder

TMS374 ECU DECODER

A handy tool to have that will decode an all the above ecu's to a new state without the need of a laptop!

Introduction:

This Tool is a frequency sweeper with 5V square wave output (Duty cycle 50%, effective frequency range from over 10kHz (max 50kHz) to 50Hz). This tool can be also considered as a MCU version of the software TMS-374 Decoder ECU. The only difference between the two tools is that the MCU version works without a PC. A small MCU is used to generate the pulses instead of the PC RS232 Tx line.

The TMS 374 software is in fact a simple frequency sweeper with an effective range from about 2000Hz to about 100Hz. The Tiny sweeper does exactly the same but much more better (bigger range). After powering the device on - the LED should blink twice. Pressing the button will start the sweep procedure. LED ON - means there are pulses on the output. After reaching the lowest frequency the LED goes off and the mcu stops the generation.

 

Connection diagram:

+ : 12v DC

- : GND

S : signal wire

 

Manual:

After powering the device on - the LED should blink twice. The sweeping process starts as power is supplied to the device. LED ON - means there are pulses on the output. After reaching the lowest frequency the LED goes off and the mcu stops the generation.

 

* Connect the GND line to any suitable GND on the ECU via the small grabber.

* Connect the Data line to the Reset pin on the EPROM via the small grabber.

* Power the ECU and then the sweeper, the sweeper will flash twice on power up.

* Press the button and the device will start sweeping, once the LED turns off your done.

* Cut the immo data line on the ECU before re-fitting back to car.

 

TMS-374 Decoder ECU info

The sweeper should work with the following ECUs:

 

Renault SIEMENS Fenix 3 and 5

Renault Megane 1400cc 8v

Renault Megane 1600cc 8v

Renault Megane 2000cc 8v

Renault Megane 2000cc 16V

Renault Megane Scenic 1400cc 8v

Renault Megane Scenic 1600cc 8v

Renault Megane Scenic 2000cc 8v

Renault Sefrane 2000cc 16V

Renault Laguna 2000cc 8v

Renault Laguna 2000cc 16v

Renault Espace 2000cc 8v

 

Renault SAGEM SAFIR 1 and 2

Renault Clio 1200cc 8V

Renault Clio 1400cc 8V

Renault Clio 1600cc 8V

Renault Clio 2000cc 16V Williams

Renault Laguna 1800cc 8V

Renault Laguna 2000cc 8V

Renault Laguna 1800cc 16V

Renault Laguna 2000cc 16V

Renault Twingo 1200cc 8V

 

NOTE: If reset pin is connected to ground then it must be lifted or the track cut before decoding. This can be re-attached after decoding the ecu. As a rule of thumb keep the power connected to the ECU for a futher five minutes after the decoder has completed the decoding process.

 

Sagem SL96 Psa

Peugeot 306 1400cc 8V

Peugeot 306 1600cc 16V

Peugeot 306 1800 16V

Peugeot Ranch 1400 8V

Citroen Berlingo 1400cc 8V

Citroen Xrara 1400cc 8V

Citroen Xrara 1800cc 16V

 

DAEWOO SIEMENS

Daewoo Matiz 800cc

 

HYUNDAI SIEMENS

Hyundai Coupe 1600cc 16V

Hyundai Coupe 2000cc 16V

 

KIA SIEMENS

Kia Rio 1300 16V

Kia Rio 1500 16V

 

MAGNETI MARELLI

1AP20, 1AP40, 1AP41, 1AP43, 1AP80, 1AP81, 1AP83 1AP90,

Citroen Berlingo 1800cc 8V

Citroen Saxo 1400cc 8V

Citroen Saxo 1600cc 16V

Citroen Xara 1400cc 8V

Citroen Xara 1800cc 8V

Citroen Xara 2000cc 16V

Citroen ZX 1400cc 8V

Peugeot 106 1400cc 8V

Peugeot 106 1600cc 8V

Peugeot 106 1600cc 16V

Peugeot 206 1100cc 8V

Peugeot 206 1400cc 8V

Peugeot 306 1400cc 8V

Peugeot 306 1600cc 8V

Peugeot 306 1800cc 8V

Peugeot 405 1800cc 8V

Peugeot 406 1800cc 8V

Peugeot Partner 1800 8V

 

 

TMS-374

1AP\SAGEM\SIEMENS

 

 

Procedure:

Simply power the ECU and device using a suitable 12V power supply. Connect the GND cable to a good ground source on the ECU and then the data line to the Reset Pin on the flash 27c512 or 28F512 as shown in the diagram.

Start the device and wait for it to finish its cycle (the led will turn off). At this point the ECU has been decoded and put into a new state. The Immo line will need to be disconnected before the ECU is re-fitted back to the car.

 

 

CENTRALINE SAGEM SAFIR RENAULT 35 PIN

PIN 18 --- 12v+

PIN 4\34 --- GND

PIN 30 Immo data line (cut)

 

CENTRALINE SAGEM SAFIR 1 RENAULT 55 PIN

PIN 1 --- 12v+

PIN 2\3\18 --- GND

PIN 37 Immo line (cut)

 

 

CENTRALINE SAGEM SAFIR 2 RENAULT 55 PIN

PIN 1 --- 12v+

PIN 2\3\18 --- GND

PIN 37 Immo data line (cut)

 

 

CENTRALINE SIEMENS DAEWOO (MATIZ) 55 PIN

PIN 32\24 --- 12V+

PIN 2\3 --- GND

PIN 11 Immo data line (cut)

 

 

CENTRALINE SIEMENS RENAULT 55 PIN

PIN 32\24\1 --- 12V+

PIN 2\3 --- GND

PIN 37 Immo data line on 1600 cc (cut)

PIN 35 Immo data line on 1800cc\2000 cc (cut)

 

 

CENTRALINE 1AP 55 PIN

PIN 35\13 --- 12v+

PIN 54\36 --- GND

PIN 27\48 Immo data line (cut)

 

 

CENTRALINE SIEMENS HUNDAY 55 PIN

 

 

CENTRALINE SAGEM SL96 PSA

Pin 1 --- 12v+

Pin 2\3\18 --- GND

Pin 27\48 Immo data line (cut)


Contact Information:
Live Support: Chat with us online
Common Questions: info@ecutool.com
Technical Support: support@ecutool.com
Complains: complains@ecutool.com
MSN: info@sinosells.com
Skype: wangbaiyi
Facebook: www.facebook.com/ecutoolwang
Ask A Question: You can go to your member centre and submit your questions.
Address: Shenzhen BaoAn Longhua MinZhi Boulevard HuaTongYuan Logistics Center B6-416

If you are not satisfied with our customer service staff, please send email to complains@ecutool.com.

Video for TMS374 ECU Decoder

  • Not Available

Software for TMS374 ECU Decoder

  • Not Available

Documents for TMS374 ECU Decoder

Configuration for TMS374 ECU Decoder

F.A.Q for TMS374 ECU Decoder

1.What can this item do?
The TMS 374 software is in fact a simple frequency sweeper with an effective range from about 2000Hz to about 100Hz, will decode an all the above ecu's to a new state without the need of a laptop.

2.What car or module can be supported by this item?
It support Renault SIEMENS Fenix 3 and 5,Renault SAGEM SAFIR 1 and 2,Sagem SL96 Psa,DAEWOO SIEMENS,HYUNDAI SIEMENS,KIA SIEMENS,MAGNETI MARELLI.

3.What all I can get if I buy this item?
You can get TMS374 ECU Decoder.

4.What can I do if the item has problem?
You can have specific technical support to deal with it by e-mail service@ecutool.com OR Remote Support. You can learn more from http://www.ecutool.com/help.html.

5.How long wil the item quality guarantee?
we offer one year's quality guarantee for all products sold in www.ecutool.com. You can request replacement or money back within 30 days after the item is delivered.

6.What is your return policy?
Authorized return must be shipped prepaid. Unless authorized and prepaid, return will be delayed in processing. Note: For your own protection, insure return shipment.You can learn more from http://www.ecutool.com/policy.html .

More...Related Items for TMS374 ECU Decoder

Comments for TMS374 ECU Decoder

    by rabee7878, 06:23:00, 2013-8-24
Item No. 3502054
Item Name TMS374 ECU Decoder

Please i want buy this item (TMS374 ECU Decoder)

Do you accept (Western Union) transfer money , if yes please send my your W/U information ...

Best regards
Rabee.

Replied, by admin, at 11:11:00, 2013-8-24

Yes. we receive it. Make order then pay it.
http://www.ecutool.com/help.html



PayPal/Credit Card (online)



Add the item(s) to the cart and check out online with your PayPal or credit card. For detailed procedures, please click HERE.

Western Union (30 minutes)



Go to your local Western Union agency and make payment to:

First name: BEI

Last name: WEN

Country: China (city is shenzhen, if required)

Please email me the following information after payment:

First name in the payment sheet

Last name in the payment sheet

Control number of the payment

Country in the payment sheet

Important: for easy and quick confirmation of your payment, please do not fix the exchange rate of money.

Rating:
User Name:
Password:
Comments:
Code:
   
Join our community:
Newsletter get Coupon:
 
SKP-900 | VPC-100 | Car Emulators | X-431 | TRUCK DIAG KING | Diagnostic Tools | Odometer Correction | Key Programmers
MSN: info@sinosells.com, Email: info@ecutool.com
Copyright, China ECU Tools Centre, 2007-2015
ICP Certificate No. 09097225